By using our website, you agree to the use of our cookies.
01925 812809 info@grpukltd.com Unit 19 Riverside Ind Est, Woolston, Warrington

Shop

GC 65PA Clear
GC 65PA Clear

Scott Bader 65PA Gelcoat Brush (Clear) 225kg

£695.25

How To Order

£3.09 per kg ex-vat

Clear Brushing GelCoat, isophthalic brushing polyester gelcoat (standard viscosity). General purpose, high quality moulding gelcoat for hand lay-up in GRP work. For brush application, free from air and can be used clear or pre-pigmented with high quality pigment pastes. The product is free from drainage and has excellent weathering properties as well as very good water resistance.

Coverage is approximately 800g per square metre. Dependent on temperature.

Lloyds Approved.

SKU: 2009 Categories:,

Product Description

Features and Benefits

Crystic Gelcoat 65PA has excellent water and weather resistance.

Approvals

Crystic Gelcoat 65PA is approved by Lloyd’s Register of Shipping for use in the construction of craft under their survey. When backed with Crystic 356PA, it is capable of obtaining a Class 1 certificate to BS476 Part 7 and of satisfying the requirements of the Building Regulations for a Class O structure. The same laminate can also achieve an M1 rating to the French Epiradiateur NFP 92-501 test.

Formulation

Crystic Gelcoat 65PA should be allowed to attain workshop temperature (18ºC-20°C) before use. Stir well by hand, or with a low shear mixer to avoid aeration, and then allow to stand to regain thixotropy. Crystic Gelcoat 65PA requires only the addition of catalyst to start the curing reaction. The recommended catalyst is Butanox M50 (or other equivalent catalyst), which should be added at 2% into the gelcoat. (Please consult our Technical Service Department if other catalysts are to be used). The catalyst should be thoroughly incorporated into the gelcoat, with a low shear mechanical stirrer where possible.

Pot Life

Temperature Pot Life In Minutes
15ºC 24
20ºC 15
25ºC 9

The gelcoat, mould and workshop should all be at, or above, 15ºC before curing is carried out.

Application

For normal moulding, the application of Crystic Gelcoat 65PA should be controlled to 0.4-0.5mm (0.015-0.020 inch) wet film thickness. As a guide, approximately 450-600 g/m2 of gelcoat mixture (depending on pigment) will give the required thickness when evenly applied.

Recommended Testing

It is recommended that customers test all pigmented gelcoats before use under their own conditions of application to ensure the required surface finish is achieved.

Additives

Crystic Gelcoat 65PA is supplied in a wide range of colours. This eliminates the potential for mixing errors with small quantities of pigment paste. The addition of fillers or pigments can adversely affect the water and weather resistance of the cured gelcoat. Crystic Gelcoat 65PA can be used as a topcoat provided that 2% Crystic Solution MW is added to overcome the normal tackiness.

Physical Data – Uncured

The following tables give typical properties of Crystic Gelcoat 65PA when tested in accordance with SB, BS, EN or BS EN ISO test methods.

Property Unit Liquid Gelcoat
Appearance Mauvish, Cloudy
Viscosity at 25ºC Thixotropic
Specific Gravity at 25ºC 1.11
Volatile Content % 34
Stability at 20ºC Months 3
Geltime at 25ºC Using 2% Butanox M50

(or Other Equivalent Catalyst)

Minutes 9

 

Physical Data – Cured

Property Unit

Fully Cured *Gelcoat

(Unfilled Casting)

Barcol Hardness (Model GYZJ 934-1) 42
Water Absorption 24 hrs at 23ºC mg 18
Deflection Temperature Under Load† (1.80 MPa) ºC 75
Elongation at Break % 3.0
Tensile Strength MPa 75
Tensile Modulus MPa 3500

* Curing Schedule – 24hrs at 20ºC, 3hrs at 80ºC.

† Curing Schedule – 24hrs at 20ºC, 5hrs at 80ºC, 3hrs at 120ºC.

Post-Curing

Satisfactory laminates for many applications can be made with Crystic Gelcoat 65PA by curing at workshop temperature

(20ºC). However, for optimum properties, laminates must be post-cured before being put into service. The moulding

should be allowed to cure for 24 hours at 20ºC, and then be oven-cured for 3 hours at 80ºC.

Storage

Crystic Gelcoat 65PA should be stored in its original container and out of direct sunlight. It is recommended that the

storage temperature should be less than 20ºC where practical, but should not exceed 30ºC. Ideally, containers should be

opened only immediately prior to use.

Packaging

Crystic Gelcoat 65PA is supplied in 1Kg, 5Kg, 25Kg and 225Kg containers.

Health and Safety

See separate Material Safety Data Sheet.

 

 

Data Sheets

Technical Data Sheet (TDS)
Technical Data Sheet (TDS)
WordPress Theme built by Shufflehound. Copyright (c)  GRP[UK] LTD 2017 - All Rights Reserved - Web Design and Hosting by TADAH