By using our website, you agree to the use of our cookies.
01925 812809 info@grpukltd.com Unit 19 Riverside Ind Est, Woolston, Warrington

Shop

RTS Iso Tooling Gelcoat Grey (20.8kg)

£99.22

How To Order

Product description

BÜFA®-ISO Gelcoat 3000-I-1 is a fast cure pre-accelerated, thixotropic

isophthalic gelcoat ready for use. This gelcoat is a non pigmented brush

gelcoat suitable for use in general moulding applications. BÜFA®-ISO

Gelcoat 3000-I-1 is intended to be tinted in the desired colour tone by

addition of colour pastes.

Applications

BÜFA®-ISO Gelcoat 3000-I-1 is suitable for moulded parts that are

subjected to heavy weathering or normal hydrolysis loads (e.g. in boat

construction, vehicle parts, shower trays etc).

SKU: 2150 Categories:,

Product Description

Specifications /technical data

Property Test method Value Unit

Viscosity at 25 °C

Brookfield RV/DV-II

spl 6. rpm 5.

ISO 2555 31390 – 42500 mPas

Viscosity at 25 °C

Brookfield RV/DV-II

spl 6. rpm 50.

ISO 2555 7300 – 8500 mPas

Styrene content 31 – 35 %

Flash point DIN 53 213 34 °C

Curing Reactivity:

BÜFA method in accordance with DIN 16 945 6.2.2.1

(100 g gelcoat + 1.0 g Butanox M-50)

25 – 35 °C 13 – 17 min

25 °C – Tmax 21,3 – 23,3 min

Tmax 162 – 198 °C

 

Attention!

The information given above refers exclusively to the use of the catalyst

named and the quantity specified. The use of different products or

differing quantities may yield different results. Density depends on

pigmentation.

Colouring

BÜFA®-ISO Gelcoat 3000-I-1 can be supplied in most RAL colours and a

number of other shades. It is also available as an unpigmented base

gelcoat with higher viscosity and reactivity under Product No. 655-2000.

Pigmented gelcoats are produced via the Eurotinter system, with fast

colour matching service available.

 

Properties of the cured base resin

Property* Test method Value

Tensile strength ISO 527-2 85,5 MPa

Tensile E-modulus ISO 527-2 3400 MPa

Tensile elongation ISO 527-2 4,0 %

Heat distortion

temperature (HDT) ISO 75-A approx. + 92 °C

* Measured in a standard laboratory atmosphere on cast test specimens made of pure

resin that were conditioned for 24 hours at + 80 °C.

 

Directions for use

Our release agent system BF 500 /BF 700 has been tested and

successfully used with this gelcoat. Before using other release agents,

they should be tested for suitability under practical conditions. If

circumstances permit, we recommend post-curing the moulded part for

several hours at 80 °C so that optimal gelcoat properties are achieved.

For more information on working and curing, see the notes in our

Technical Information leaflet, “Working with BÜFA® -Gelcoats”.

Storage/Handling

BÜFA®-ISO Gelcoat 3000-I-1 is available in 20 kg and 200 kg

packaging.This product must be stored cool in closed containers,

protected from sunlight. Shelf-life is at least 4 months in unopened,

original containers stored up to a temperature of 20 °C. Gel and curing

times may change with increasing duration of storage.

Data Sheets

Material Safety Data Sheet (MSDS)
Material Safety Data Sheet (MSDS)
WordPress Theme built by Shufflehound. Copyright (c)  GRP[UK] LTD 2017 - All Rights Reserved - Web Design and Hosting by TADAH